Senco PC1010 1-Horsepower Peak, 1/2 hp running 1-Gallon Compressor Review
| Product Code | B0000AQK78 |
| Product Rating |  |
| Price | $114.99 |
| Where To Buy | See More Details |
| Customer Review | See More Reviews |
Product Details
- Amazon Sales Rank: #1624 in Home Improvement
- Brand: Senco
- Model: PC1010 Compressor
- Dimensions: 10.00" h x
13.00" w x
14.00" l,
20.00 pounds
Features
- Lightweight and portable--easy to carry from site to site as you work
- One horsepower peak ,1/2 horsepower runningand one-gallon capacity
- Ideal for a range of renovation and home improvement jobs, as well as for hobbies and crafts
- Delivers 20 to 44 drives per minute
- Backed by a one-year warranty
- Lightweight and portable--easy to carry from site to site as you work
- One horsepower peak ,1/2 horsepower runningand one-gallon capacity
- Ideal for a range of renovation and home improvement jobs, as well as for hobbies and crafts
- Delivers 20 to 44 drives per minute
- Backed by a one-year warranty
Product Description
Includes PC1010, 1 Gallon Electric Oil-Less Hand-Carry Compressor - PC1010
Customer Reviews
Most helpful customer reviews
173 of 174 people found the following review helpful.
Easy on the arm!
By Bob Hagen
As a general contractor I have several compressors. At least 90% of the time I grab an Emglo because they do everything I need except texturing. But I've grown fond of this little Senco WHEN IT IS USED PROPERLY! That means if I have a small trim project or a VERY small framing project it does the job, and both takes up less room and is a lot easier to pack around. It'll drive 3" framing nails no problem...when the tank is topped off, but the last couple nails before the compressor cycles always need to be hammer finished. Same is true for 15 or 18 gauge finish nails. When the tank is just about to cycle the nails don't completely set. My workers love the Senco...much to my chagrin. For one, it's light, and second...it takes FOREVER to refill (relatively speaking) and my guys love to stand there with their thumbs you know where taking a break every 10 to 15 nails or so! So if used for small jobs...or trim where you nail one piece at a time while cutting, well then it's a champ. But if you tend to cut trim for an entire room, then want to shoot it on quick...this Senco will frustrate you no end. You end up hand nail setting too many nails, or else you have to stop frequently, unhook the air hose, drain a little air from the tank until it cycles, then wait for the darn thing to fill. If you use it right... 5 stars. If you use it as your go to compressor... 2.5 stars tops. I hope this helps!
180 of 182 people found the following review helpful.
Have compressor will travel
By Wilbur Wong
This is a great second compressor. I wouldn't buy this as a primary or first compressor but it works fine to support small nail guns. My other portable weighs 68 pounds and will keep up with 1 to 2 framing or roofing nailers. My shoulders ache from the number of times I have lugged it up 78 steps to a job site. This goes anywhere with a bunch of tools in the other hand.
Other than nail guns, NO it won't do much at 0.7 cu ft per min when paint spray guns need 10 times that, and a blow gun will empty the tank in 10 seconds or less. But seriously, this compressor gives me at least 10 shots from my 16 ga finish nailer before the motor kicks in; a couple more off of an 18 ga finish nailer, and as an acid test, I got 3 shots from a 3 1/4 inch framing nailer (not recommended but if all I need is 10 nails I'd rather carry this in - especially considering that my ripe old age keeps me from doing much serious hammering!)
Last word, the first one I received had a leaky reed valve and it had to be replaced by Amazon - I'm very happy with the replacement and have used it on several job sites.
75 of 76 people found the following review helpful.nifty little trim compressor
By Scott Freeland
For my applications of easy carry in and out, it's been terrific for lightweight 18ga. finishing.On a small renovation project yesterday, 4 doors jambs and trim were easy (1" to 2" 18/16ga brads) The very least of my problems was waiting for the little Senco to catch up. Been using it for about 5 months, shot about 10,000 brads. So far it's been flawless.Very low noise as compressors go, and neat little rubber suction feet that keep it from skidding around and marring up a nice floor.
Post a Comment